Tommy - Wheel Bearing Hub Puller Removal Kits: Ford or Subaru or Combo

Tips for Using Wheel Bearing Hub Removal Tool (Ford & Subaru):

• Striking the bearing with an air hammer at an angle as if to rotate the bearing, prior to mounting Tommy, and during the extraction of Tommy is recommended.
• Use of the air hammer will break the corrosive bond between the bearing and its knuckle.
• Check your grease gun before use to ensure they have wheel bearing grease vs. ball joint grease. ProMaxx recommends our Anti-Wear Extreme Pressure Grease (PMXPPG016).
• Consider pairing this item with the Tommy Rail: This accessory works with our Tommy Wheel Bearing Puller and allows technicians to apply even more force to the wheel hub to make any wheel bearing removal quick and easy.

How to Use Tommy Wheel Bearing Puller Tool

TOMMY - Wheel Bearing Puller Tool Kit for Ford & Subaru

• FOR FORD APPLICATIONS: Before mounting the Wheel Hub Flange Assembly (image “C”), remove the (4) bearing hub bolts from the rear of the knuckle, the axle nut, and the (5) wheel mounting studs as well as the screws that secure the backplate. It is not necessary to completely remove the backplate, however, it is preferred because it provides additional clearance for the mounting fasteners. If left intact, simply rotate the backplate to allow a flat contact surface of the Tommy pushrods against the knuckle. FOR SUBARU APPLICATIONS: LEAVE THE AXLE NUT IN PLACE and remove the ABS brake sensor (2015-2020 rear), the five-wheel mounting studs, the four-bearing hub bolts and the parking brake assembly. For electronic emergency brake applications, see image “E” and proceed to step 2 (on next page).
• With the ProMAXX Logo facing you as shown in image “A”, screw the three pushrods into the top plate in the locations marked (1) and hand tighten for Ford applications. For Subaru applications, slip the notched push rods into the top plate straddling the bearing. Then secure by placing the included nylon and neoprene flat washer on the pushrod with the nylon washer on top. Tighten with the knurled hand nut so that the pushrod is firmly secured. TIP: Place the three pushrods into the bearing hub to identify the matching location of each pushrod on the top plate. Mark the location with a paint stick for future uses in Ford or Subaru.
• Place a thin film of the included Tommy Extreme Pressure Lithium grease on the pushrods and assemble Tommy by passing the mounted pushrods over the wheel hub flange assembly. Ensure that the pushrod protrudes through the bearing hub and straddle the bearing hub as shown in image “B”. Now that you have determined which of the three-wheel mounting holes you will use for the pushrods, use the (2) hex bolts, flat washers, and hex nuts placed through two remaining two holes in the hub to secure the wheel hub assembly as shown in image “D”. TIP: Leave the pushrods in the flange so they operate freely without binding while you tighten the two mounting bolts. Check these periodically while using your impact gun and air hammer as they may loosen.
• Now assembled, tighten the two mounting bolts securely, using caution, to ensure that the Tommy wheel hub flange assembly is precisely parallel to the bearing hub and ALL FIVE LEVELING SCREWS THAT ARE PRE-INSTALLED IN TOMMY ARE IN CONTACT WITH THE WHEEL MOUNTING FLANGE. If any of the five leveling screws are not in contact with the bearing hub, loosen the extraction bolt and tighten the two (2) hex mounting bolts until all leveling screws make contact. When using your air hammer, check often to ensure they have not vibrated loose. Tighten as necessary.
• Add a “golf ball” size amount of TOMMY heavy-duty EXTREME PRESSURE wheel bearing grease to the threads of the extraction bolt. Apply the grease under and between the two (2) bearing flange washers and the flange of the extraction bolt. Insert the extraction bolt through the pushrod flange into the hub flange assembly as shown in image “A” (previous page). BALL JOINT GREASE WILL NOT PROVIDE SUFFICIENT LUBRICATION FOR USE OF THE DEVICE. Check to make sure each push rod is in equal contact with the vehicle knuckle that straddles the wheel bearing hub. Ensure that all pushrods are, once again, seated flat against the backplate if intact. The TOMMY Subaru Model includes 360° adjustable pushrods with notched tips. These can be turned to the correct angle to fully make contact with the knuckle. For Subaru 2015 and newer models without the emergency brake, utilize the two (2) TOMMY PushRod Plates to improve the rigidity of the stock Subaru backing plate as in image “E”. Simply add some ProMAXX® grease to the rear of the backing plate to act as an adhesive to hold them in place until they are in contact with the Tommy push rods.
• Using a pneumatic air hammer, pre-strike (shock) all four mounting corners of the bearing hub for a minimum of five seconds at an angle as if to rotate the bearing hub. Using a high-torque impact gun, attach a 1 ¼” impact socket and turn the extraction bolt until it makes contact with the pushrod flange. Tighten for five (5) seconds putting the entire assembly under tension and then STOP. Using an air hammer once again, strike the base of the bearing housing at an angle for a minimum of five seconds each (as if you are trying to rotate the bearing hub assembly). Avoid striking the lobes where the mounting threads are - deforming these will prevent the TOMMY tool from mounting, see image “F.”

Tommy Wheel Bearing Puller PDF